Incomplete referenced artifact analysis
- Category
- analysis-evasion
- Confidence
- 100% confidence
- Finding
Referenced artifact was not completely inspected
- Content
md 求解器、样例或模型生成的数据均须满足[数据契约](references/schematic-data.md#数据驱动架构基准);不强制某个求解器。
Security audit
Security checks for vulnerabilities and agentic risk
ClawScan rates this skill suspicious with high confidence because it reports an unverified installer that runs a downloaded script and several confirmed weaknesses in design-editing and verification workflows; some scanner coverage is incomplete.
Consider avoiding installation until the installer can be independently verified and the reported design-workflow weaknesses and incomplete scan coverage have been reviewed. If you proceed, understand that the scan does not establish malicious intent, but it also cannot confirm that all referenced content was fully inspected.
Referenced artifact was not completely inspected
求解器、样例或模型生成的数据均须满足[数据契约](references/schematic-data.md#数据驱动架构基准);不强制某个求解器。
Referenced artifact was not completely inspected
| 原理图数据、布局与 Apply | [数据契约](references/schematic-data.md)、[执行步骤](references/auto-layout-sop.md) |
Referenced artifact was not completely inspected
完成前按[布局规则](references/pcb-layout.md)通过连续两轮自检,第二轮包含保存重载和新回读;修复后重来。
Referenced artifact was not completely inspected
| PCB 布局与机械 | [PCB](references/pcb.md)、[布局](references/pcb-layout.md) |
Referenced artifact was not completely inspected
| 需求、选型与设计取舍 | [设计流程](references/design-flow.md)、[决策参考](references/design-decisions.md)、[器件选型](references/part-selection.md) |
Referenced artifact was not completely inspected
| 库器件或自建库 | [选型](references/part-selection.md)、[建库](references/library-authoring.md)、[候选表](references/standard-parts.json) |
Referenced artifact was not completely inspected
| 原理图检查或局部修复 | [原理图](references/schematic.md)、[放置](references/schematic-placement.md)、[连接](references/schematic-wiring.md) |
Referenced artifact was not completely inspected
| PCB 布局与机械 | [PCB](references/pcb.md)、[布局](references/pcb-layout.md) |
Referenced artifact was not completely inspected
| 由已有 PCB 生成 3D 打印外壳(上下壳/推盖、开孔、螺丝柱、卡扣) | [参数化外壳](references/pcb.md#参数化外壳离线生成-stl) |
Referenced artifact was not completely inspected
| PCB 布线、铺铜与禁布区 | [布线](references/pcb-routing.md) |
Referenced artifact was not completely inspected
| 连接、升级或保存异常 | [环境配置](references/environment-setup.md)、[Action 边界](references/actions.md) |
Piping the network response directly into bash converts remotely supplied bytes into executable instructions without a verification boundary. This is the same bootstrap supply-chain exposure identified by SC2, rather than separate evidence of malicious chaining, but it can still yield arbitrary execution under the user's account.
发布版安装 CLI 和 Skill:
curl -fsSL https://raw.githubusercontent.com/zhoushoujianwork/easyeda-agent/main/install.sh | bash
easyeda update --check
easyeda update
Tool parameters are crafted to achieve unintended or unsafe behavior. Parameter abuse can bypass intended safety checks (e.g. shell=True, --force, dangerous glob patterns).
irst** (reports paths/lines/arcs WITHOUT mutating — safe on any board, even one you don't want to change), then run for real and `pcb save`. Flags: `--selected` (only tracks selected in EasyEDA, default whole board), `--net` (**repeatable** — `--net USB_DP --net USB_DM` beautifies only those nets; the safest way to apply on a dense board — small blast radius, dry-run + DRC each net), `--layer` filter, `--force-arc` (round even too-short segments), `--merge-u` (fuse tight U-bends into one arc), `--no-protect`/`--no-drc`/`--no-pour-rebuild`. **On a dense, not-yet-DRC-clean board prefer per-net over a full-board pass** — a whole-board run both has a large blast radius and surfaces the board's pre-existing violations alongside its own. Absorbed from the open-source **Easy_EDA_PCB_Beautify** (m-RNA, Apache-2.0; see repo `NOTICE`). Line-width bezier smoothing is a documented follow-up. Advice from upstream: pad-to-track joints may need a manual look, exclude RF/high-speed nets from a global
Tool parameters are crafted to achieve unintended or unsafe behavior. Parameter abuse can bypass intended safety checks (e.g. shell=True, --force, dangerous glob patterns).
### 从已完成原理图直接提取
优先使用现场 `sch read --no-check` 的制造网表,不再从 PDF 重猜连接;再用 `lib by-lcsc`
将每个供应商编号解析成 32 位 Device UUID。公开 `*.topology.json` 必须把原位号转换为模块内
角色、把匿名网改为 `internal.*`、把跨模块网改为 `port.*`,并保留全部物理引脚。只有
`sch read.floatingPins` 明确列出的脚才能记录为 `connectionState:"unconnected"`;字段缺失不能
Without declared permissions the skill's intent is opaque and cannot be validated.
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content
Suspicious Unicode normalization or mixed-script content